OCD Notices, Requests, Permits and Reports

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
APD	Main Form	True	True
C-102 (Plat)	C-102	True	True	* Plat Survey (Pad Diagram)
NGMP	Natural Gas Management Plan	False	False	* Introduced by NMCA 19.15.27.9 D
Casing	Additional Casing Information	True	True
Dir Survey	Directional Drilling Plan	False	False	* Required for horizontal wells.
H2S	H2S Plan	False	False	* Required only in a location where H2S present
Closed Loop	Closed Loop or Pit Plan	True	True
Kick Off	Kick-off Points	False	False
Formation Tops	Formation Tops	True	True
Potash Notice	Notice to POTASH leaseholders with one mile	False	False	* See hearing order R-111-Q for details
BOP	Blow Out Prevention	True	True
Plugging Plan	Plugging Plan	False	False	* If pilot hole is plugged

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Federal 3160-3	Main Form	True	True
C-102 (Plat)	C-102	True	True	* Plat Survey (Pad Diagram)
NGMP	Natural Gas Management Plan	True	True	* Introduced by NMCA 19.15.27.9 D
Drilling/Casing	Drilling and Casing Plan	True	True
Dir Survey	Directional Drilling Plan	False	False	* Required for horizonal/directional wells
Federal COA	Federal Conditions of Approval	False	False
H2S	H2S Plan	False	False	* Required only in a location where H2S present
Closed Loop	Closed Loop or Pit Plan	True	True
Kick Off	Kick-off Points	False	False
Formation Tops	Formation Tops	True	True
Potash Notice	Notice to POTASH leaseholders with one mile	False	False	* See hearing order R-111-Q for details
BOP	Blow Out Prevention	True	True
Plugging Plan	Plugging Plan	False	False	* If pilot hole is plugged

Click again to collapse NMAC

19.15.7.8 D. (1)       form C-101 - application for permit to drill, deepen or plug back;

19.15.7.12       APPLICATION FOR PERMIT TO DRILL, DEEPEN OR PLUG BACK (Form C-101): Form C-101 is the form an operator uses to apply for a permit to drill, deepen, re-enter or plug a well back to a different pool or complete or re-complete a well in an additional pool.

19.15.7.36       FORMS REQUIRED ON FEDERAL LAND:
            A.       An operator shall use federal forms in lieu of state forms when filing application for permit to drill, deepen or plug back and sundry notices and reports on wells and well completion or recompletion report and log for wells on federal lands in New Mexico. However, the operator shall submit two extra copies of each of the forms to the BLM, which, upon approval, will transmit the forms to the division. An operator of a well on federal land shall use the following BLM forms in lieu of division forms:

BLM Form No.	Title of Form (Same for both agencies)	Form No.
3160-3 (Nov. 1993)	Application for Permit to Drill, Deepen or Plug Back	C-101
3160-5 (Nov. 1983)	Sundry Notices and Reports on Wells	C-103
3160-4 (Nov. 1983)	Well Completion or Recompletion Report and Log	C-105

            B.       The above forms as the BLM may revise are the only forms that an operator may file in place of division forms.
            C.       After a well is completed and ready for pipeline connection, the operator shall file form C-104 along with a copy of form C-105 or BLM form No. 3160-4, whichever is applicable, with the division on wells drilled in the state, regardless of land status. Further, the operator shall file production reports using division forms; the division will not accept federal forms for reporting production.
            D.       An operator’s failure to comply with 19.15.7.36 NMAC shall result in the division’s cancellation of form C-104 for the affected well or wells.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-102	Main Form	True	True
Dir Survey	As Drilled-Directional Survey	False	False
Kick Off	Kick Off Point	False	False
Formation Tops	Formation Tops	False	False

Click again to collapse NMAC

19.15.7.8 D. (2)       form C-102 - well location and acreage dedication plat;

19.15.7.13       WELL LOCATION AND ACREAGE DEDICATION PLAT (Form C-102):
            A.       Form C-102 is a dual purpose form the operator uses to show the well’s exact location and the acreage dedicated to the well. The form is also used to show the ownership and status of each lease contained within the dedicated acreage. When there is more than one working interest or royalty owner on a given lease, designation of the majority owner et al. is sufficient.
            B.       An operator shall fill out and certify the information required on form C-102 except the well location on the plat. A professional surveyor, registered in the state of New Mexico, or surveyor approved by the division, shall plot and certify the well location on the plat from the section’s outer boundaries.
            C.       An operator shall file amended form C-102 in the event there is a change in the information the operator previously submitted. The operator does not need to provide certification of the well location when filing amended form C-102.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103B	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103A	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
C-102	C-102	False	False	* With change of location or pool changes
Plan Revision	Plan Revision	True	True
NGMP	Natural Gas Management Plan	False	False	* Introduced by NMCA 19.15.27.9 D
BLM COA	BLM Conditions Of Approval	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103C	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103E	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
C-102	C-102	False	False	* Required when adding a new formation/zone
Work Plan	Work Plan	True	True
Wellbore Schematic	Wellbore Schematic	False	False
NGMP	Natural Gas Management Plan	False	False	* Required when adding a zone or additional perforations
BLM COA	BLM Conditions Of Approval	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103F	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
Plugging Plan	Plugging Plan	True	True
Current Wellbore Schematic	Current Wellbore Schematic	True	True
Proposed Wellbore Schematic	Proposed Wellbore Schematic	True	True
BLM COA	BLM Conditions Of Approval	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103G	Main Form	True	True
Work Plan	Work Plan	True	True
Current Wellbore Schematic	Current Wellbore Schematic	True	True
Proposed Wellbore Schematic	Proposed Wellbore Schematic	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103H	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
BLM COA	BLM Conditions Of Approval	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103I	Main Form	True	True
Work Plan	Work Plan	True	True
Current Wellbore Schematic	Current Wellbore Schematic	True	True
Proposed Wellbore Schematic	Proposed Wellbore Schematic	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103N	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103P	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
Plugging Report	Plugging Report	True	True
Wellbore Schematic	Wellbore Schematic	True	True	* Subsequent wellbore schematic needs to reflect downhole conditions and any adjustments made during plugging operations. If no changes were made from NOI refile previous wellbore schematic for completed P&A record.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Marker Photographs	Marker Photographs	True	True
Site Photographs	Site Photographs	False	False
Pipeline Layout	Pipeline layout including legal description and surface ownership	False	False	* Required if leaving pipeline(s)
Radiation Survey	Results of radiation survey along pipeline route	False	False	* Required if leaving pipeline(s)
Pipeline Material Type	Type of material used the pipeline	False	False	* Required if leaving pipeline(s)
Pipeline Flushing Procedure	Procedure used for flushing pipeline	False	False	* Required if leaving pipeline(s)
Explanation of Benefit	Explanation why it is more beneficial to leave the pipeline	False	False	* Required if leaving pipeline(s)
Proof of Notice	Proof notices sent to all surface owners where the pipeline is located	False	False	* Required if leaving pipeline(s)

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103R	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
Work Plan	Work Plan	True	True
Pressure Test-Charts	Pressure Test - Mechanical Integrity Chart	False	False	* Required if casing changes
Updated Wellbore Schematic	Updated Wellbore Schematic	False	False	* Required if casing changes

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103T	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
Completion Work	Completion Work	True	True
Wellbore Schematic	Wellbore Schematic	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103U	Main Form	True	True
Work Plan	Work Plan	True	True
Pressure Test-Chart	Pressure Test - Mechanical Integrity Chart	True	True
Updated Wellbore Schematic	Updated Wellbore Schematic	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103V	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103X	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
BLM COA	BLM Conditions Of Approval	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103Z	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103

Click again to collapse NMAC

19.15.7.8 D. (3)       form C-103 - sundry notices and reports on wells;

19.15.7.14       SUNDRY NOTICES AND REPORTS ON WELLS (Form C-103): Form C-103 is a dual purpose form the operator files with the appropriate division district office to obtain division approval prior to commencing certain operations and to report various completed operations.
            A.       Form C-103 as a notice of intention.
                        (1)       An operator shall file form C-103 and obtain the division’s approval prior to:
                                    (a)       effecting a change of plans from those the division previously approved on form C-101 or form C-103;
                                    (b)       altering a drilling well’s casing program or pulling casing or otherwise altering an existing well’s casing installation;
                                    (c)       making multiple completions in a well;
                                    (d)       placing a well in approved temporary abandonment;
                                    (e)       plugging and abandoning a well;
                                    (f)       performing remedial work on a well that, when completed, will affect the well’s original status (this includes making new perforations in existing wells or squeezing old perforations in existing wells, but does not apply to new wells in the process of being completed nor to old wells being deepened or plugged back to another zone when the division has authorized the recompletion by an approved form C-101, application for permit to drill, re-enter, deepen plug back or add a zone, nor to acidizing, fracturing or cleaning out previously completed wells, nor to installing artificial lift equipment); or
                                    (g)       downhole commingling in well bores, within pools or areas that the division has established as pre-approved pools or areas.
                        (2)       In the case of well plugging operations, the notice of intention shall include a detailed statement of the proposed work including plans for shooting and pulling casing; plans for mudding, including the mud’s weight; plans for cementing, including number of sacks of cement and depths of plugs; restoration and remediation of the location; and the time and date of the proposed plugging operations. The operator shall file a complete log of the well on form C-105 with the notice of intention to plug the well, if the operator has not previously filed the log (see 19.15.7.16 NMAC); the division shall not release the financial assurance until the operator complies with this requirement.
            B.       Form C-103 as a subsequent report.
                        (1)       The operator shall file form C-103 as a subsequent report of operations in accordance with 19.15.7.14 NMAC as applicable to the particular operation being reported.
                        (2)       The operator shall use form C-103 in reporting such completed operations as:
                                    (a)       commencement of drilling operations;
                                    (b)       casing and cement test;
                                    (c)       altering a well’s casing installation;
                                    (d)       work to secure approved temporary abandonment;
                                    (e)       plugging and abandonment;
                                    (f)       plugging back or deepening within the same pool;
                                    (g)       remedial work;
                                    (h)       installation of artificial lifting equipment; or
                                    (i)       other operations that affect the well’s original status but that are not specifically covered in 19.15.7.14 NMAC.
            C.       Report of commencement of drilling operations. Within 10 days following the commencement of drilling operations, the operator shall file a report of commencement on form C-103. The report shall indicate the hour and the date the operator spudded the well.
            D.       Report of results of test of casing and cement job; report of casing alteration. The operator shall file a report of casing and cement test within 10 days following the setting of each string of casing or liner. The operator shall file the report on form C-103 and include a detailed description of the test method employed and the results obtained by the test and any other pertinent information 19.15.16.10 NMAC requires. The report shall also indicate the top of the cement and the means by which the operator determined the top. It shall also indicate any changes from the casing program previously authorized for the well.
            E.       Report of temporary abandonment. The operator shall file a notice of work to secure approved temporary abandonment within 30 days following the work’s completion. The report shall present a detailed account of the work done on the well, including location and type of plugs used, if any, and status of surface and downhole equipment and any other pertinent information relative to the well’s overall status.
            F.       Report on plugging of well.
                        (1)       The operator shall file a report of plugging operations within 30 days following completion of plugging operations on a well. The operator shall file the report on form C-103, which shall include the date the operator began plugging operations and the date the operator completed the work, a detailed account of the manner in which the operator performed the work including the depths and lengths of the various plugs set, the nature and quantities of materials employed in the plugging operations including the weight of the mud used, the size and depth of all casing left in the hole and any other pertinent information. (See 19.15.25 NMAC regarding plugging operations.)
                        (2)       The division shall not approve a plugging report until the operator demonstrates compliance with Subsection B of 19.15.25.10 NMAC. The operator shall contact the appropriate division district office when the operator has restored the location in order to arrange for a division representative’s inspection of the plugged well and the location.
            G.       Report of remedial work. The operator shall file a report of remedial work performed on a well within 30 days following the work’s completion. The operator shall file the report on form C-103 and present a detailed account of the work done and the manner in which the operator performed the work; the daily production of oil, gas and water both prior to and after the remedial operation; the size and depth of shots; the quantity and type of crude, chemical or other materials the operator employed in the operation; and any other pertinent information. Among the remedial work an operator shall report on form C-103 are the following:
                        (1)       report on shooting, fluid fracturing or chemical treatment of a previously completed well;
                        (2)       report of squeeze job;
                        (3)       report on setting of liner or packer;
                        (4)       report of installation of pumping equipment or gas lift facilities; or
                        (5)       report of any other remedial operations that are not specifically covered herein.
            H.       Report on deepening or plugging back within the same pool. An operator shall file a report of deepening or plugging back within 30 days following completion of the operations on a well. The operator shall file the report on form C-103 and present a detailed account of work done and the manner in which the operator performed the work. If the operator recompletes the well in the same pool, the operator shall also report the daily production of oil, gas and water both prior to and after recompletion. If the well is recompleted in another pool, the operator shall file forms C-101, C-102, C-104 and C-105 in accordance with 19.15.7.12 NMAC, 19.15.7.13 NMAC, 19.15.7.15 NMAC and 19.15.7.16 NMAC.
            I.       Other reports on wells. The operator shall submit reports on other operations that affect the well’s original status but that are not specifically covered in 19.15.7.14 NMAC to the division on form C-103 10 days following the operation’s completion.

19.15.7.36       FORMS REQUIRED ON FEDERAL LAND:
            A.       An operator shall use federal forms in lieu of state forms when filing application for permit to drill, deepen or plug back and sundry notices and reports on wells and well completion or recompletion report and log for wells on federal lands in New Mexico. However, the operator shall submit two extra copies of each of the forms to the BLM, which, upon approval, will transmit the forms to the division. An operator of a well on federal land shall use the following BLM forms in lieu of division forms:

BLM Form No.	Title of Form (Same for both agencies)	Form No.
3160-3 (Nov. 1993)	Application for Permit to Drill, Deepen or Plug Back	C-101
3160-5 (Nov. 1983)	Sundry Notices and Reports on Wells	C-103
3160-4 (Nov. 1983)	Well Completion or Recompletion Report and Log	C-105

            B.       The above forms as the BLM may revise are the only forms that an operator may file in place of division forms.
            C.       After a well is completed and ready for pipeline connection, the operator shall file form C-104 along with a copy of form C-105 or BLM form No. 3160-4, whichever is applicable, with the division on wells drilled in the state, regardless of land status. Further, the operator shall file production reports using division forms; the division will not accept federal forms for reporting production.
            D.       An operator’s failure to comply with 19.15.7.36 NMAC shall result in the division’s cancellation of form C-104 for the affected well or wells.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-104RT	Main Form	True	True	* Current OCD C-104 form
C-102	C-102 As Drilled	False	False	* Required "As Drilled" Plat for horizontal/directional wells
Directional Survey	As Drilled-Directional Survey	False	False	* Required for horizontal/directional wells
Deviation Survey	Deviation Survey	False	False	* Required for vertical wells

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-104NW/RC	Main Form	True	True	* Current OCD C-104 form
C-102	C-102 As Drilled	True	True	* Required "As Drilled" Plat for horizontal/directional wells
Directional Survey	As Drilled-Directional Survey	False	False	* Required for horizontal/directional wells
Deviation Survey	Deviation Survey	False	False	* Required for vertical wells
C-105	C-105	True	True	* Current OCD C-105 form, or approved BLM equivalent
Wellbore Schematic	Wellbore Schematic	False	False	* Detailed wellbore schematic for New Completions
C-103	C-103 Misc	False	False
BLM Form	BLM Approved Forms	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-104CT	Main Form	True	True	* Current OCD C-104 form
Request Confidential Status	Request for “Tight Hole” Confidential status	True	True	* File per NMAC 19.15.7.16 C. Special processing directives to be put in place
C-102	C-102 As Drilled	True	True	* Required "As Drilled" Plat for horizontal/directional wells
Directional Survey	As Drilled-Directional Survey	False	False	* Required for horizontal/directional wells
Deviation Survey	Deviation Survey	False	False	* Required for vertical wells
C-105	C-105	True	True	* Current OCD C-105 form, or approved BLM equivalent
Wellbore Schematic	Wellbore Schematic	False	False
C-103	C-103 Misc	False	False
BLM Form	BLM Approved Forms	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-104	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-104C	Main Form	True	True
C-102	C-102	False	False	* Required "As Drilled" Plat for horizontal/directional wells
Directional Survey	As Drilled-Directional Survey	False	False	* Required for horizontal/directional wells
Deviation Survey	Deviation Survey	False	False	* Required for vertical wells
Kick Off	Kick-off Points	False	False
C-103	C-103 Completion Sundry	False	False
C-105	C-105	False	False
Wellbore Schematic	Wellbore Schematic	False	False
C-103	C-103 Misc	False	False	* File for: additional completion information if it was not provided on completion sundry; i.e. tubing-well test data; 1st delivery notice

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-104CT	Main Form	True	True
Request Confidential Status	Request for Confidential “Tight Hole” status	True	True	* File per NMAC 19.15.7.16 C. Special processing directives to be put in place
C-102	C-102	False	False	* Required "As Drilled" Plat for horizontal/directional wells
Directional Survey	As Drilled-Directional Survey	False	False	* Required for horizontal/directional wells
Deviation Survey	Deviation Survey	False	False	* Required for vertical wells
Kick Off	Kick-off Points	True	True
C-103	C-103 Completion Sundry	True	True
C-105	C-105	True	True
Wellbore Schematic	Wellbore Schematic	True	True
C-103	C-103 Misc	False	False	* File for: additional completion information if it was not provided on completion sundry; i.e. tubing-well test data; 1st delivery notice

Click again to collapse NMAC

19.15.7.8 D. (4)       form C-104 - request for allowable and authorization to transport oil and gas;

19.15.7.15       REQUEST FOR ALLOWABLE AND AUTHORIZATION TO TRANSPORT OIL AND GAS (Form C-104): An operator shall file with the division a complete form C-104 to request the division assign an allowable to a newly completed or re-completed well or a well completed in an additional pool or issue an operator authorization to transport oil or gas from the well.

19.15.7.16       WELL COMPLETION OR RECOMPLETION REPORT AND LOG (Form C-105):
            C.       The division shall not keep form C-105 and accompanying attachments confidential unless the well’s owner requests in writing that the division keep it confidential. Upon such request, the division shall keep these data confidential for 90 days from the date of the well’s completion, provided, however, that the report, logs and other attached data may, when pertinent, be introduced in a public hearing before division examiners, the commission or in a court of law, regardless of the request that they be kept confidential.

19.15.16.14       DEVIATION TESTS AND WELLBORE SURVEYS; VERTICAL, DEVIATED AND DIRECTIONAL WELLS:
            A.       Vertical and deviated well bores.
                        (1)       Deviation tests required. An operator shall test a vertical or deviated well that is drilled or deepened at reasonably frequent intervals to determine the deviation from the vertical. The operator shall make the tests at least once each 500 feet or at the first bit change succeeding 500 feet. The operator shall file with the division along with its form C-104 a tabulation of deviation tests run that is sworn to and notarized.
                        (2)       Excessive deviation. When the deviation averages more than five degrees in a 500-foot interval, the operator shall include the calculations of the hole’s maximum possible horizontal displacement. When the maximum possible horizontal displacement exceeds the distance to the appropriate unit’s nearest outer boundary line the operator shall run a directional survey to establish the location of the well’s completed interval.
                        (3)       Unorthodox well locations. If the results of the directional survey of a vertical or deviated well indicate that the completed interval is more than 50 feet from the approved surface location and closer than the minimum setback requirements to the applicable unit’s outer boundary, then the well is considered unorthodox. To obtain authority to produce the well, the operator shall file an application with the division’s Santa Fe office, and shall follow the process outlined in Subsection C of 19.15.15.13 NMAC to obtain approval of the unorthodox well location.
                        (4)       Directional survey requirements. Upon the director’s request, the operator shall directionally survey a vertical or deviated well. The operator shall file directional surveys run on a well, in division-approved format, with the division upon the well’s completion. The division shall not approve a form C-104 for the well until the operator has filed the directional surveys.
            B.       Directional well bores.
                        (1)       Directional drilling. The appropriate division district office may grant a permit to directionally drill a well bore if every point of the completed interval is projected to be located at a distance greater than or equal to the minimum setback distance from the applicable spacing unit’s outer boundaries or at an unorthodox well location the division previously approved.
                        (2)       Unorthodox well locations. If all or part of a directional well’s completed interval is projected to be located less than the minimum distance from the outer boundary of the well’s spacing unit, the well’s location is considered unorthodox. To obtain approval for the well’s location, the operator shall file an application in the division’s Santa Fe office in accordance with Subsection C of 19.15.15.13 NMAC.
                        (3)       Directional surveys required. An operator shall run a directional survey on each well drilled pursuant to Subsection B of 19.15.16.14 NMAC. The operator shall file a directional survey, in division-approved format, with the division upon the well’s completion. The division shall not approve a form C-104 for the well until the operator files the directional survey. The well’s location will be considered unorthodox if the directional survey indicates that part of a well’s completed interval, as drilled, is located more than 50 feet from its projected location and closer to an outer boundary of the spacing unit than applicable minimum setback distance. For previously approved unorthodox well locations, the well’s as-drilled location is unorthodox if the directional survey indicates that any part of the completed interval is located more than 50 feet (or, if less, twenty-five percent of the previously authorized distance) closer to the outer boundary of the spacing unit than the approved location.
            C.       Directional survey specifications. Directional surveys that 19.15.16.14 NMAC requires shall have shot points no more than 200 feet apart and shall be run by competent surveying companies. The division shall allow exceptions to the minimum shot point spacing provided the survey’s accuracy is still within acceptable limits.

19.15.16.15       HORIZONTAL WELLS:
            E.       Other matters.
                        (1)       Directional survey requirements. The operator of each horizontal well shall run a directional survey and file the directional survey, in a division-approved format, upon the well’s completion. Directional surveys shall have shot points no more than 200 feet apart and shall be run by competent surveying companies. The division shall allow exceptions to the minimum shot point spacing provided the survey’s accuracy is still within acceptable limits. The division shall not approve a form C-104 for the well until the operator has filed the required directional survey.

19.15.16.16       MULTIPLE COMPLETIONS; BRADENHEAD GAS WELLS:
            A.       Multiple completions.
                        (1)       Filing. An operator intending to multiple complete shall file form C-101 or C-103 with the division for approval before completing and C-104 after completing along with information required by the form instructions.

19.15.16.20       ALLOWABLES AND AUTHORIZATION TO TRANSPORT OIL AND GAS:
            A.       The division may assign an allowable to a newly completed or re-completed well or a well completed in an additional pool or issue an operator authorization to transport oil or gas from the well if the operator:
                        (1)       has filed a complete form C-104;
                        (2)       has provided a sworn and notarized tabulation of all deviation tests the operator has run on the well, and directional surveys with calculated bottom hole location, in accordance with the requirements of 19.15.16.14 NMAC or 19.15.16.15 NMAC;
                        (3)       has dedicated a standard spacing unit or horizontal spacing unit for the pool in which the well is completed, a standard spacing unit or horizontal spacing unit has been communitized or pooled and dedicated to the well or the division has approved a non-standard spacing unit or horizontal spacing unit; and
                        (4)       complies with Subsection A of 19.15.5.9 NMAC.
            B.       The allowable the division assigns to an oil well is effective at 7:00 a.m. on the completion date, provided the division receives form C-104 during the month of completion. The date of completion shall be that date when new oil is delivered into the stock tanks. Unless otherwise specified by special pool orders, the allowable the division assigns to a gas well is effective at 7:00 a.m. on the date of connection to a gas transportation facility, as evidenced by an affidavit of connection from the transporter to the division, or the date of receipt of form C-104 by the division, whichever date is later.

19.15.18.19       GATHERING, TRANSPORTING AND SALE OF DRIP:
            A.       The waste of drip is prohibited when it is economically feasible to salvage the drip.
            B.       A person may move and sell drip, provided it complies with 19.15.18.19 NMAC.
            C.       A person shall not transport or sell drip until the gas transporter files form C-104 designating the drip transporter authorized to remove the drip from its gas gathering or transportation system.

19.15.23.8       DOCUMENTATION REQUIRED:
            A.       Off-lease transportation of oil or lease condensate by motor vehicle shall be pursuant to an approved form C-104 and shall be accompanied by a run ticket or equivalent document. The documentation shall identify the transporter’s name and address, the operator’s name, the name of the lease or facility from which the oil was taken, the date of removal, the API gravity of the oil, the observed percentage of BS&W, the volume of oil or opening and closing tank gauges or meter readings and the driver’s signature. The document shall provide space for recording of the lease number and for the signature of the operator or the operator’s representative.

19.15.24.11       PRODUCTION OF LIQUID HYDROCARBONS FROM GAS WELLS:
            A.       Liquid hydrocarbons produced incidental to the authorized production of gas from a well the division has classified as a gas well are legal production.
            B.       For purposes of 19.15.24.11 NMAC the division shall consider gas produced from a gas well to be authorized production with the following exceptions:
                        (1)       when the operator produces the well without an approved form C-104, designating the gas transporter and the oil or condensate transporter for the well; or
                        (2)       when the division has directed the operator to shut-in the well.
            C.       In the event the division directs an operator to shut-in a gas well, the operator and the division shall immediately notify both the gas transporter and oil transporter.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-105	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-4 in lieu of division Form C-105

Click again to collapse NMAC

19.15.7.8 D. (5)       form C-105 - well completion or recompletion report and log;

19.15.7.16       WELL COMPLETION OR RECOMPLETION REPORT AND LOG (Form C-105):
            A.       Within 45 days following the completion or recompletion of a well, the operator shall file form C-105 with the appropriate division district office accompanied by a summary of special tests conducted on the well, including drill stem tests. In addition, the operator shall file a copy of electrical and radio-activity logs run on the well with form C-105. If the division does not receive form C-105 with attached logs and summaries within the specified 45-day period, the division shall withhold the allowable for the well until the operator has complied with 19.15.7.16 NMAC.
            B.       In the case of a dry hole, a complete record of the well on form C-105 with the attachments listed in Subsection A of 19.15.7.16 NMAC shall accompany the notice of intention to plug the well, unless previously filed. The division shall not approve the plugging report or release the bond the operator has complied with 19.15.7.16 NMAC.
            C.       The division shall not keep form C-105 and accompanying attachments confidential unless the well’s owner requests in writing that the division keep it confidential. Upon such request, the division shall keep these data confidential for 90 days from the date of the well’s completion, provided, however, that the report, logs and other attached data may, when pertinent, be introduced in a public hearing before division examiners, the commission or in a court of law, regardless of the request that they be kept confidential.

19.15.7.36       FORMS REQUIRED ON FEDERAL LAND:
            A.       An operator shall use federal forms in lieu of state forms when filing application for permit to drill, deepen or plug back and sundry notices and reports on wells and well completion or recompletion report and log for wells on federal lands in New Mexico. However, the operator shall submit two extra copies of each of the forms to the BLM, which, upon approval, will transmit the forms to the division. An operator of a well on federal land shall use the following BLM forms in lieu of division forms:

BLM Form No.	Title of Form (Same for both agencies)	Form No.
3160-3 (Nov. 1993)	Application for Permit to Drill, Deepen or Plug Back	C-101
3160-5 (Nov. 1983)	Sundry Notices and Reports on Wells	C-103
3160-4 (Nov. 1983)	Well Completion or Recompletion Report and Log	C-105

            B.       The above forms as the BLM may revise are the only forms that an operator may file in place of division forms.
            C.       After a well is completed and ready for pipeline connection, the operator shall file form C-104 along with a copy of form C-105 or BLM form No. 3160-4, whichever is applicable, with the division on wells drilled in the state, regardless of land status. Further, the operator shall file production reports using division forms; the division will not accept federal forms for reporting production.
            D.       An operator’s failure to comply with 19.15.7.36 NMAC shall result in the division’s cancellation of form C-104 for the affected well or wells.

19.15.16.19       LOG, COMPLETION AND WORKOVER REPORTS:
            A.       Completion report. Within 45 days after the completion of a well drilled for oil or gas, or the recompletion of a well into a different common source of supply, the operator shall file a completion report with the division on form C-105. For the purpose of 19.15.16.19 NMAC, a hole drilled or cored below fresh water or that penetrates oil- or gas-bearing formations or that an owner drills is presumed to be a well drilled for oil or gas. The operator shall signify on form C-105, or alternatively on form C-103, whether the well has been hydraulically fractured.
            B.       Hydraulic fracture disclosure. For a hydraulically fractured well, the operator shall also complete and file with the FracFocus chemical disclosure registry a completed hydraulic fracturing disclosure within 45 days after completion, recompletion or other hydraulic fracturing treatment of the well. The hydraulic fracturing disclosure shall be completed on a then current edition of the hydraulic fluid product component information form published by FracFocus and shall include complete and correct responses disclosing all information called for by the FracFocus form, provided that:
                        (1)       the division does not require the reporting of information beyond the material safety data sheet data as described in 29 C.F.R. 1910.1200;
                        (2)       the division does not require the reporting or disclosure of proprietary, trade secret or confidential business information; and
                        (3)       the division shall download and archive New Mexico FracFocus submissions on a quarterly basis.
            C.       If the FracFocus chemical disclosure registry is temporarily inoperable, the operator of a well on which hydraulic fracturing treatment(s) were performed shall file the information required by the then most recent FracFocus form with the division along with Well Completion Report (form C-105) or Sundry Notice (form C-103) reporting the hydraulic fracture treatment and file the information on the FracFocus internet website when the website is again operable. If the FracFocus chemical disclosure registry is discontinued or becomes permanently inoperable, the operator shall continue filing the information with the division until otherwise provided by rule or order.

19.15.26.8       INJECTION OF FLUIDS INTO RESERVOIRS:
            G.       Storage wells.
                        (1)       The director may grant administratively, without hearing, an application for the underground storage of liquefied petroleum gas or liquid hydrocarbons in secure caverns within massive salt beds, provided the applicant has complied with the notice provisions of Subsection B of 19.15.26.8 NMAC and the division receives no objections pursuant to Subsection C of 19.15.26.8 NMAC.
                        (2)       In addition to the filing requirements of Subsection B of 19.15.26.8 NMAC, the applicant for approval of a storage well under Subsection G of 19.15.26.8 NMAC shall file the following:
                                    (a)       with the director, financial assurance in accordance with the provisions of 19.5.8 NMAC; and
                                    (b)       with the appropriate division district office:
                                                (i)       form C-101;
                                                (ii)       form C-102; and
                                                (iii)       form C-105.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-106	Main Form	True	True
Facility Diagram	Facility Diagram	False	True
Compliance Plan	Compliance Plan	False	True
Well Plat	Well Plat	False	True
C-102	C-102	False	True	* For included wells
Wellsite Diagram	Wellsite Diagram	False	True
Midstream Approval Evidence	Evidence of Approval from Midstream	False	True

Click again to collapse NMAC

19.15.7.8 D. (6)       form C-106 - notice of intention to utilize automatic custody transfer equipment;

19.15.7.17       NOTICE OF INTENTION TO UTILIZE AUTOMATIC CUSTODY TRANSFER EQUIPMENT (Form C-106): An operator intending to use an ACT system shall file form C-106, when applicable, in accordance with Subsection A of 19.15.18.15 NMAC.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-107A	Main Form	True	True
Summary	Summary of proposal	True	True
Current Well Diagram	Current Well Diagram	True	True
Proposed Well Diagram	Proposed Well Diagram	True	True	* After proposed alterations
Proposed Allocation	Proposed Allocation and Supporting Data	True	True	* Depending on allocation method
Commingling Statement	Commingling will Not Reduce Value Statement	True	True	* Statement that commingling will not reduce the total remaining production's value
Notified Persons w/ Tracking	List of Notified Persons and Tracking Numbers	False	True	* Required if ownership is diverse as defined by 19.15.12.7(A) NMAC
No Protests Statement	No Received Protests Statement	False	False	* Required if ownership is diverse as defined by 19.15.12.7(A) NMAC
Identical Ownership Statement	Identical Ownership Statement	False	False	* Required if ownership is identical as defined by 19.15.12.7(B) NMAC
Proof of BLM/SLO Notice	Proof of BLM/SLO Notice	False	False	* Required if Federal or State lands are involved
Gas Sample	Gas Sample	False	False	* Required if pools are not commonly commingled
Water Sample	Water Sample	False	False	* Required if pools are not commonly commingled
Administrative Checklist	Administrative Application Checklist	False	False	* Department Use Only Attachment
Correspondence	Correspondence	False	False	* Department Use Only Attachment
OCD Review	OCD Review	False	False	* Department Use Only Attachment
Signed Order	Signed Order	False	True	* Department Use Only Attachment

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-107B	Main Form	True	True
Summary	Summary of proposal	True	True
Proposed Allocation	Proposed Allocation and Supporting Data	False	False	* Not required for OLM
Lease Map	Lease Map	True	True	* Lease map with wells, laterals, and facilities depicted
Facility Diagram	Facility Diagram	False	False	* Not required for OLM
Commingling Statement	Commingling will Not Reduce Value Statement	False	False	* Statement that commingling will not reduce the total remaining production's value
Notified Persons w/ Tracking	List of Notified Persons and Tracking Numbers	False	False	* Required if ownership is diverse as defined by 19.15.12.7(A) NMAC
Identical Ownership Statement	Identical Ownership Statement	False	False	* Required if ownership is identical as defined by 19.15.12.7(B) NMAC
Proof of BLM/SLO Notice	Proof of BLM/SLO Notice	False	False	* Required if Federal or State lands are involved
C-102	C-102	False	False	* C-102s for each well
Comm./Pool. Agreement	Communitization/Pooling Agreement	False	False	* Communitization or pooling agreements if applicable
Administrative Checklist	Administrative Application Checklist	False	False	* Department Use Only Attachment
Correspondence	Correspondence	False	False	* Department Use Only Attachment
OCD Review	OCD Review	False	False	* Department Use Only Attachment
Signed Order	Signed Order	False	True	* Department Use Only Attachment

Click again to collapse NMAC

19.15.7.8 D. (7)       form C-107 - application for multiple completion;
                        (8)       form C-107-A - application for downhole commingling;
                        (9)       form C-107-B - application for surface commingling (diverse ownership);

19.15.7.18       APPLICATION FOR MULTIPLE COMPLETION (Form C-107): An operator shall file form C-107, when applicable, in accordance with Subsection A of 19.15.16.15 NMAC.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-108	Main Form	True	True
C-102	C-102	True	True
Wellbore Diagram	Wellbore Diagram	True	True
Proof of Notice	Proof of Notice	True	True
AOR Analysis	Area Of Review Analysis	True	True
Tabulation of Wells	Tabulation of wells in Area Of Review	True	True	* Including diagrams for penetrating wells
Fluid Analysis	Injectate and Formation Fluid Analysis	True	True
Seismicity Analysis	Seismicity Analysis	True	True	* For high volume Devonian wells , especially near faults
Operational Details	Operational Details	True	True
Support Doc	Supporting Documentation	False	False	* For OCD use only

Click again to collapse NMAC

19.15.7.8 D. (10)       form C-108 - application to dispose of salt water by injection into a porous formation;

19.15.7.19       APPLICATION FOR AUTHORIZATION TO INJECT (Form C-108): An operator shall file form C-108 in accordance with Subsection B of 19.15.26.8 NMAC.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-109	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (11)       form C-109 - application for discovery allowable and creation of a new pool;

19.15.7.20       APPLICATION FOR DISCOVERY ALLOWABLE AND CREATION OF A NEW POOL (Form C-109): An operator shall file form C-109, when applicable, in accordance with 19.15.20.16 NMAC.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-111	Main Form	True	True
C-111A	C-111A, Gas Receipts Continuation Sheet	False	False	* Required if needed
C-111B	C-111B, Gas Disposition Continuation Sheet	False	False	* Required if needed

Click again to collapse NMAC

19.15.7.8 D. (12)       form C-111 - gas transporter’s monthly report (sheet 1 and sheet 2);

19.15.7.21       GAS TRANSPORTER’S MONTHLY REPORT (Form C-111):
            A.       An operator shall complete and maintain for the division’s inspection, form C-111 monthly in accordance with Subsections B, C and D of 19.15.7.21 NMAC. The transporter shall itemize information on sheet no. 2 of form C-111 by pool, by operator and by lease, in alphabetical order.
            B.       An operator of a gas gathering system, gas transportation system, recycling system, fuel system, gas lift system, gas drilling operation, etc. shall complete and maintain for division inspection form C-111 each month. The form shall cover gas, casinghead gas and carbon dioxide gas taken into a system during the preceding month and shall show the gas’ source and its disposition.
            C.       An operator of a gasoline plant, cycling plant or other plant at which gasoline, butane, propane, kerosene, oil or other products are extracted from gas within the state shall complete and maintain for the division’s inspection form C-111 each month. The form shall cover gas, casinghead gas and carbon dioxide gas the plant has taken during the preceding month and shall show the gas’ source and its disposition. If an operator owns more than one plant in a given division district, the operator shall file sheet no. 1 of form C-111 for each plant. In preparing sheet no. 2, the operator shall consolidate requisitions for plants in the district, itemized in the order described in the Subsection A of 19.15.7.21 NMAC.
            D.       Where a producer takes gas and uses it for any of the above uses, the producer shall complete and maintain for division inspection form C-111 itemizing such gas. The producer shall also include this gas on form C-115. The producer shall also include gas used on the lease from which it was produced for consumption in lease houses, treaters, compressors, combustion engines and other similar equipment, or gas that is flared, on the form C-115 but shall not include it on form C-111.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-112	Main Form	True	True
C-112A	C-112A, Receipts Continuation Sheet	False	False	* Required if needed
C-112B	C-112B, Deliveries Continuation Sheet	False	False	* Required if needed

Click again to collapse NMAC

19.15.7.8 D. (13)       form C-112 - transporter’s and storer’s monthly report;
                        (14)       form C-112-A - receipts continuation sheet;
                        (15)       form C-112-B - deliveries continuation sheet;

19.15.7.22       TRANSPORTER’S AND STORER’S MONTHLY REPORT (Form C-112): A transporter or storer of oil and liquid hydrocarbons within the state shall complete and maintain for division inspection for each calendar month a form C-112 containing complete information and data indicated by the form respecting stocks of oil and liquid hydrocarbons on hand and receipts and deliveries of oil and liquid hydrocarbons by pipeline and trucks within the state, and receipts and deliveries from leases to storers or refiners; between transporters within the state; between storers and refiners within the state.

Click again to collapse NMAC

19.15.7.8 D. (17)       form C-115 - operator’s monthly report;
                        (18)       form C-115-EDP - operator’s monthly report (electronic data processing);

19.15.7.24       OPERATOR’S MONTHLY REPORT (Form C-115):
            A.       An operator shall file a form C-115 for each non-plugged well completion for which the division has approved a form C-104 and for each secondary or other enhanced recovery project or pressure maintenance project injection well or other injection well within the state, setting forth complete information and data indicated on the forms in the order, format and style the director prescribes. The operator shall estimate oil production from wells producing into common storage as accurately as possible on the basis of periodic tests.
            B.       An operator shall file the reports 19.15.7.24 NMAC requires using the division’s web-based online application on or before the 15th day of the second month following the month of production, or if such day falls on a weekend or holiday, the first workday following the 15th. An operator may apply to the division for exemption from the electronic filing requirement based upon a demonstration that such requirement would operate as an economic or other hardship.
            C.       If an operator fails to file a form C-115 that the division accepts, the division shall, within 30 days of the appropriate filing date, notify the operator by electronic mail or letter of its intent to cancel the operator’s authorization to transport or inject if the operator does not file an acceptable and complete form C-115. The notice shall inform the operator of the right to request a hearing pursuant to 19.15.4.8 NMAC. If the operator does not either file an acceptable and complete form C-115 or request a hearing on the proposed cancellation within 60 days of the original due date of the form C-115, the division may cancel the operator’s authority to transport from or inject into all wells it operates.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-116	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (19)       form C-116 - gas-oil ratio tests;

19.15.7.25       GAS-OIL RATIO TESTS (Form C-116): An operator shall make and report gas-oil ratio tests on form C-116 as prescribed in 19.15.18.8 NMAC and applicable special pool orders. The operator shall file the form C-116.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-117A	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-117AF	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-117B	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (20)       form C-117-A - tank cleaning, sediment oil removal, transportation of miscellaneous hydrocarbons and disposal permit;
                        (21)       form C-117-B - monthly sediment oil disposal statement;

19.15.7.26       TANK CLEANING, SEDIMENT OIL REMOVAL, TRANSPORTATION OF MISCELLANEOUS HYDROCARBONS AND DISPOSAL PERMIT (Form C-117-A) AND MONTHLY SEDIMENT OIL DISPOSAL STATEMENT (Form C-117-B):
            A.       An operator shall file form C-117-A with the appropriate division district office in accordance with Subsections B, C and H of 19.15.18.17 NMAC.
            B.       An operator shall file form C-117-B with the division’s Santa Fe office and the appropriate division district office in accordance with Subsection D of 19.15.18.17 NMAC.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-118	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (22)       form C-118 - treating plant operator’s monthly report (sheet 1 and sheet 2);

19.15.7.27       TREATING PLANT OPERATOR’S MONTHLY REPORT (Form C-118): A treating plant operator shall file on a monthly basis form C-118 with the appropriate division district office. The form C-118 shall contain all the information the form requires. Column 1 of sheet 1-A of form C-118 entitled permit number, references form C-117-A, for each lot of oil the operator picked up for processing.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-120A	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (23)       form C-120-A - monthly water disposal report;

19.15.7.28       MONTHLY WATER DISPOSAL REPORT (Form C-120-A): An operator of a salt water disposal system shall report its operations on form C-120-A. The operator shall file form C-120-A in duplicate, with one copy to the division’s Santa Fe office and one copy to the appropriate division district office, and shall postmark the form no later than the 15th day of the second succeeding month.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-122	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-122A	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (26)       form C-122 - multi-point and one point back pressure test for gas wells;
                        (27)       form C-122-A - gas well test data sheet-San Juan basin (initial deliverability test, blue paper; annual deliverability test, white);
                        (28)       form C-122-B - initial potential test data sheet;
                        (29)       form C-122-C - deliverability test report;
                        (30)       form C-122-D - worksheet for calculation of static column wellhead pressure (Pw);
                        (31)       form C-122-E - worksheet for stepwise calculation of (surface) (subsurface) pressure (Pc and Pw);
                        (32)       form C-122-F - worksheet for calculation of wellhead pressures (Pc or Pw) from known bottom hole pressure (Pf or Ps);
                        (33)       form C-122-G - worksheet for calculation of static column pressure at gas liquid interface;

19.15.7.30       MULTIPOINT AND ONE POINT BACK PRESSURE TEST FOR GAS WELL (Form C-122):
            A.       Gas well test data sheet - San Juan basin (form C-122-A)
            B.       Initial potential test data sheet (form C-122-B)
            C.       Deliverability test report (form C-122-C)
            D.       Worksheet for calculation of static column wellhead pressure (Pw) (form C- 122-D)
            E.       Worksheet for stepwise calculation of (surface) (subsurface) pressure (Pc & Pw) (Pf & Ps) (form C-122-E)
            F.       Worksheet for calculation of wellhead pressures (Pc or Pw) from known bottom hole pressure (Pf or Ps) (form C-122-F)
            G.       Worksheet for calculation of status column pressure at gas liquid interface (form C-122-G). The operator shall file the forms listed in Subsections A through F of 19.15.7.30 NMAC with the appropriate division district office in accordance with the provisions of the manual for back-pressure testing of natural gas wells or gas well testing manual for northwest New Mexico, 19.15.19.8 NMAC and applicable special pool orders and proration orders.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-123	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (34)       form C-123 - request for the creation of a new pool;

19.15.7.31       REQUEST FOR THE CREATION OF A NEW POOL (Form C-123): The appropriate division district office shall provide the operator of a well that requires the creation of a pool written instructions regarding the filing of form C-123.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-126	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (37)       form C-126 - permit to transport recovered load oil;

19.15.7.34       PERMIT TO TRANSPORT RECOVERED LOAD OIL (Form C-126): An applicant to transport recovered load oil shall file form C-126 with the appropriate division district office in conformance with 19.15.20.15 NMAC.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-127	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (38)       form C-127 - request for allowable change;

19.15.7.35       REQUEST FOR ALLOWABLE CHANGE (Form C-127): An oil producer shall file form C-127 with the appropriate division district office not later than the 10th day of the month preceding the month for which an oil producer is requesting oil well allowable changes.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Compositional Analysis	Compositional analysis of vented or flared natural gas	True	True
Volume Calculation	Calculations or Specific Justification for the Volumes	True	True	* Determination used for Nature and Volume of Venting or Flaring
Scaled Site Map	Scaled Site Map	False	False	* Scaled sitemap with GPS coordinates showing point of venting or flaring

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Compositional Analysis	Compositional analysis of vented or flared natural gas	False	False
Volume Calculation	Calculations or Specific Justification for the Volumes	False	False	* Determination used for Nature and Volume of Venting or Flaring

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-129EX	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-131A	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-131B	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (41)       form C-131-A - monthly gas storage report;
                        (42)       form C-131-B - annual LPG storage report;

19.15.7.39       MONTHLY GAS STORAGE REPORT (Form C-131-A); ANNUAL LPG STORAGE REPORT (Form C-131-B):
            A.       An operator of an underground gas storage project shall report its operation monthly on form C-131-A. The operator shall file form C-131-A with the division’s Santa Fe office with a copy to the appropriate division district office and shall postmark it not later than the 24th day of the next succeeding month.
            B.       An operator of underground liquefied petroleum gas storage projects approved by the division shall report its operations annually on form C-131-B.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-133A	Main Form	True	True
NMDOT Warrant for Transportation	NMDOT Warrant for Transportation	False	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-133B	Main Form	True	True
NMDOT Warrant for Transportation	NMDOT Warrant for Transportation	False	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Cancel Transporting	Cancellation/No Longer Transporting	True	True

Click again to collapse NMAC

19.15.7.8 D. (43)       form C-133 - authorization to move produced water exhibit “A”;

19.15.7.40       AUTHORIZATION TO MOVE PRODUCED WATER:
            A.       A transporter of produced water shall obtain the division’s approval of form C-133 in accordance with 19.15.34 NMAC prior to transportation.
            B.       Approval of a single form C-133 is valid for leases the transporter serves.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-135	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (45)       form C-135 - gas well connection, reconnection or disconnection notice;

19.15.7.41       GAS WELL CONNECTION, RECONNECTION OR DISCONNECTION NOTICE: A gas transporter accepting gas for delivery from a wellhead or central point of delivery shall notify the division within 30 days of a new connection or reconnection to or disconnection from the gathering or transportation system by filing form C-135 with the appropriate division district office.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-136	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (46)       form C-136 - application for approval to use an alternate gas measurement method;

19.15.7.42       APPLICATION FOR APPROVAL TO USE AN ALTERNATE GAS MEASUREMENT METHOD (Form C-136):
            A.       An operator shall use form C-136 to request and obtain division approval for use of an alternate procedure for measuring gas production from a well that is not capable of producing more than 15 MCFD (Paragraph (1) of Subsection B of 19.15.19.9 NMAC) or for a well that has a producing capacity of 100 MCFD or less and is on a multi-well lease (Paragraph (2) of Subsection B of 19.15.19.9 NMAC).
            B.       An operator shall fill out the applicable information required on form C-136 with the required supplemental information attached, and file it with the appropriate division district office.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-137	Main Form	True	True
Contact Info	Contact Info of Applicant/Principle Officers/Owners of 25% or more	False	False
Survey Plat/Topo Maps	Survey Plat/Topo Maps	False	False
Surface Ownership	Surface Ownership within 1 mile of facility boundary	False	False
Construction Diagrams	Construction Plan and Diagrams	False	False
Engineering Designs	Engineering Designs, certified by a registered professional engineer	False	False
Waste Management Plan	Waste Management Plan	False	False
Inspection Plan	Inspection and Maintenance Plan	False	False
H2S Plan	H2S Prevention and Contingency Plan	False	False
Closure Plan	Closure and Post Closure Plan	False	False
Closure Cost Estimate	Closure and Post Closure Cost Estimate	False	False
Contingency Plan	Contingency Plan	False	False
Run-On/Off Plan	Run-On/Off Water Control Plan	False	False
Vadose Plan	Vadose/Water Monitor Plan	False	False
Leachate Plan	Landfill Leachate Plan	False	False
Gas Plan	Landfill Gas Safety Plan	False	False
BMP Plan	Best Management Practice (BMP) Plan	False	False
Hydro Geologic Report	Hydro Geologic Report	False	False
Geotechnical Report	Geotechnical Report	False	False
Siting Criteria	Siting Criteria Demonstration	False	False
OCD Response	OCD Response	False	False	* Department Use Only Attachment

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-137A	Main Form	True	True
Contact Info	Contact Info of Applicant/Principle Officers/Owners of 25% or more	False	False
Survey Plat/Topo Maps	Survey Plat/Topo Maps	False	False
Surface Ownership	Surface Ownership within 1 mile of facility boundary	False	False
Construction Diagrams	Construction Plan and Diagrams	False	False
Engineering Designs	Engineering Designs, certified by a registered professional engineer	False	False
Waste Management Plan	Waste Management Plan	False	False
Inspection Plan	Inspection and Maintenance Plan	False	False
H2S Plan	H2S Prevention and Contingency Plan	False	False
Closure Plan	Closure and Post Closure Plan	False	False
Closure Cost Estimate	Closure and Post Closure Cost Estimate	False	False
Contingency Plan	Contingency Plan	False	False
Run-On/Off Plan	Run-On/Off Water Control Plan	False	False
Vadose Plan	Vadose/Water Monitor Plan	False	False
Leachate Plan	Landfill Leachate Plan	False	False
Gas Plan	Landfill Gas Safety Plan	False	False
BMP Plan	Best Management Practice (BMP) Plan	False	False
Hydro Geologic Report	Hydro Geologic Report	False	False
Geotechnical Report	Geotechnical Report	False	False
Siting Criteria	Siting Criteria Demonstration	False	False
OCD Response	OCD Response	False	False	* Department Use Only Attachment

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-137B	Main Form	True	True
Contact Info	Contact Info of Applicant/Principle Officers/Owners of 25% or more	False	False
Survey Plat/Topo Maps	Survey Plat/Topo Maps	False	False
Surface Ownership	Surface Ownership within 1 mile of facility boundary	False	False
Construction Diagrams	Construction Plan and Diagrams	False	False
Engineering Designs	Engineering Designs, certified by a registered professional engineer	False	False
Waste Management Plan	Waste Management Plan	False	False
Inspection Plan	Inspection and Maintenance Plan	False	False
H2S Plan	H2S Prevention and Contingency Plan	False	False
Closure Plan	Closure and Post Closure Plan	False	False
Closure Cost Estimate	Closure and Post Closure Cost Estimate	False	False
Contingency Plan	Contingency Plan	False	False
Run-On/Off Plan	Run-On/Off Water Control Plan	False	False
Vadose Plan	Vadose/Water Monitor Plan	False	False
Leachate Plan	Landfill Leachate Plan	False	False
Gas Plan	Landfill Gas Safety Plan	False	False
BMP Plan	Best Management Practice (BMP) Plan	False	False
Hydro Geologic Report	Hydro Geologic Report	False	False
Geotechnical Report	Geotechnical Report	False	False
Siting Criteria	Siting Criteria Demonstration	False	False
OCD Response	OCD Response	False	False	* Department Use Only Attachment

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-137EZ	Main Form	True	True
Surface Owner Agreement	Surface Owner Agreement	False	False	* Required if not surface ownwer
Siting Criteria	Siting Criteria	False	False
Survey Plat/Topo Maps	Survey Plat/Topo Maps	False	False
Lab Results	Closure Laboratory Analytical Results	False	False
Photographs	Closure Photographs	False	False
OCD Response	OCD Response	False	False	* Department Use Only Attachment

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-137EZB	Main Form	True	True
Surface Owner Agreement	Surface Owner Agreement	False	False	* Required if not surface ownwer
Siting Criteria	Siting Criteria	False	False
Survey Plat/Topo Maps	Survey Plat/Topo Maps	False	False
Lab Results	Closure Laboratory Analytical Results	False	False
Photographs	Closure Photographs	False	False
OCD Response	OCD Response	False	False	* Department Use Only Attachment

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
SWMF NON-FEE SUBMITTAL	Main Form	True	True
OCD Response	OCD Response	False	False	* Department Use Only Attachment

Click again to collapse NMAC

19.15.7.8 D. (47)       form C-137 - application for waste management facility;
                        (48)       form C-137-EZ - registration/final closure report for small landfarm;

19.15.36.7 B. (9)       “Major modification” means a modification of a surface waste management facility that involves an increase in the land area that the permitted surface waste management facility occupies; a change in the design capacity or nature of the permitted oil field waste stream; addition of a new treatment process; an exception to, waiver of or change to a numerical standard provided in 19.15.36 NMAC; or other modification that the division determines is sufficiently substantial that public notice and public participation in the application process are appropriate.
                        (10)       “Minor modification” means a modification of a surface waste management facility that is not a major modification.

19.15.36.8       SURFACE WASTE MANAGEMENT FACILITY PERMITS AND APPLICATION REQUIREMENTS:
            C.       Application requirements for new facilities, major modifications and permit renewals. An applicant or operator shall file an application, form C-137, for a permit for a new surface waste management facility, to modify an existing surface waste management facility or for permit renewal with the environmental bureau in the division’s Santa Fe office. The application shall include:
                        (1)       the names and addresses of the applicant and principal officers and owners of twenty-five percent or more of the applicant;
                        (2)       a plat and topographic map showing the surface waste management facility’s location in relation to governmental surveys (quarter-quarter section, township and range); highways or roads giving access to the surface waste management facility site; watercourses; fresh water sources, including wells and springs; and inhabited buildings within one-half mile of the site’s perimeter based upon the records of the applicable county clerk or clerk’s office;
                        (3)       the names and addresses of the surface owners of the real property on which the surface waste management facility is sited and surface owners of the real property within one mile of the site’s perimeter;
                        (4)       a description of the surface waste management facility with a diagram indicating the location of fences and cattle guards, and detailed construction/installation diagrams of pits, liners, dikes, piping, sprayers, tanks, roads, fences, gates, berms, pipelines crossing the surface waste management facility, buildings and chemical storage areas;
                        (5)       engineering designs, certified by a registered professional engineer, including technical data on the design elements of each applicable treatment, remediation and disposal method and detailed designs of surface impoundments;
                        (6)       a plan for management of approved oil field wastes that complies with the applicable requirements contained in 19.15.36.13 NMAC, 19.15.36.14 NMAC, 19.15.36.15 NMAC and 19.15.36.17 NMAC;
                        (7)       an inspection and maintenance plan that complies with the requirements contained in Subsection L of 19.15.36.13 NMAC;
                        (8)       a hydrogen sulfide prevention and contingency plan that complies with those provisions of 19.15.11 NMAC that apply to surface waste management facilities;
                        (9)       a closure and post closure plan, including a responsible third party contractor’s cost estimate, sufficient to close the surface waste management facility in a manner that will protect fresh water, public health and the environment, and to comply with the closure and post closure requirements contained in Subsections A through F of 19.15.36.18 NMAC;
                        (10)       a contingency plan that complies with the requirements of Subsection N of 19.15.36.13 NMAC and with NMSA 1978, Sections 12-12-1 through 12-12-30, as amended;
                        (11)       a plan to control run-on water onto the site and run-off water from the site that complies with the requirements of Subsection M of 19.15.36.13 NMAC;
                        (12)       in the case of an application to permit a new or expanded landfill, a leachate management plan that describes the anticipated amount of leachate that will be generated and the leachate’s handling, storage, treatment and disposal, including final post closure options;
                        (13)       in the case of an application to permit a new or expanded landfill, a gas safety management plan that complies with the requirements of Subsection O of 19.15.36.13 NMAC;
                        (14)       a best management practice plan to ensure protection of fresh water, public health and the environment;
                        (15)       geological/hydrological data including:
                                    (a)       a map showing names and location of streams, springs or other watercourses, and water wells within one mile of the site;
                                    (b)       laboratory analyses, performed by an independent commercial laboratory, for major cations and anions; BTEX; RCRA metals; and TDS of ground water samples of the shallowest fresh water aquifer beneath the proposed site;
                                    (c)       depth to, formation name, type and thickness of the shallowest fresh water aquifer;
                                    (d)       soil types beneath the proposed surface waste management facility, including a lithologic description of soil and rock members from ground surface down to the top of the shallowest fresh water aquifer;
                                    (e)       geologic cross-sections;
                                    (f)       potentiometric maps for the shallowest fresh water aquifer; and
                                    (g)       porosity, permeability, conductivity, compaction ratios and swelling characteristics for the sediments on which the contaminated soils will be placed;
                        (16)       certification by the applicant that information submitted in the application is true, accurate and complete to the best of the applicant’s knowledge, after reasonable inquiry; and
                        (17)       other information that the division may require to demonstrate that the surface waste management facility’s operation will not adversely impact fresh water, public health or the environment and that the surface waste management facility will comply with division rules and orders.
            D.       Application requirements for minor modifications. Before making a minor modification, the operator of an existing surface waste management facility shall file a form C-137A with the environmental bureau in the division’s Santa Fe office describing the proposed change. Minor modifications are not subject to Subsection C of 19.15.36.8 NMAC. If the division denies the application for a minor modification, the operator may request a hearing pursuant to Subsection B of 19.15.36.10 NMAC.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-138	Main Form	True	True
Lab Results	Laboratory Analytical Results	False	False
MSD Information	MSD Information	False	False

Click again to collapse NMAC

19.15.7.8 D. (49)       form C-138 - request for approval to accept solid waste;

Click again to collapse NMAC

19.15.7.8 D. (50)       form C-139 - application for qualification of production restoration project and certification of approval;

19.15.7.43       APPLICATION FOR PRODUCTION RESTORATION PROJECT (C-139):
            A.       An operator shall use the division’s web-based online application to apply for the production restoration tax incentive.
            B.       An operator shall enter a user identification number and password that it has obtained from the division and select the well for which the operator is requesting the production restoration tax incentive. The operator shall then enter the date it began the production restoration, the date the well returned to production and the process the operator used to return the well to production. The operator shall certify that the information is complete and correct.

Click again to collapse NMAC

19.15.7.8 D. (51)       form C-140 - application for qualification of well workover project and certification of approval;

19.15.7.44       APPLICATION FOR WELL WORKOVER PROJECT (C-140):
            A.       An operator shall use the division’s web-based online application to apply for the well workover tax incentive.
            B,       An operator shall enter a user identification number and password that it has obtained from the division and select the well for which the operator is requesting the well workover tax incentive. The operator shall enter the date that it commenced the well workover and the date it completed the well workover. The operator shall attach a description of the workover procedure it performed to increase production and a production curve or data tabulation showing at least 12 months of production prior to the well workover and at least three months of production following the well workover to reflect a positive production increase.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Volume Calculation	Initial Response - Calculations or Specific Justification for the Volumes	False	False	* Determination used for Nature and Volume of Release
Water Sources	Site Characterization - Water Sources/Course Determination	False	False	* Determination of water sources and significant watercourses within ½-mile of the lateral extents of the release
Scaled Site Map	Site Characterization - Scaled Site Map	False	False	* Scaled site map showing impacted area, surface features, subsurface features, delineation points, and monitoring wells
Field Data	Site Characterization - Field Data	False	False	* Field Data
Soil Contaminant	Site Characterization - Soil Contaminant Concentration	False	False	* Data table of soil contaminant concentration data
Water Depth	Site Characterization - Water Depth Determination	False	False	* Depth to water determination
Boring Logs	Site Characterization - Boring Logs	False	False	* Boring or excavation logs
Photographs	Site Characterization - Photographs	False	False	* Photographs including date and GIS information
Topo Aerial Maps	Site Characterization - Topographic/Aerial Maps	False	False	* Topographic/Aerial maps
Lab Data	Site Characterization - Laboratory Data	False	False	* Laboratory data including chain of custody
Proposed Technique	Remediation Plan - Proposed Technique	False	False	* Detailed description of proposed remediation technique
Scaled Site Map	Remediation Plan - Scaled Site Map	False	False	* Scaled sitemap with GPS coordinates showing delineation points
Estimated Volume	Remediation Plan - Estimated Volume	False	False	* Estimated volume of material to be remediated
Closure Criteria	Remediation Plan - Closure Criteria	False	False	* Closure criteria is to Table 1 specifications subject to 19.15.29.12(C)(4) NMAC
Proposed Schedule	Remediation Plan - Proposed Schedule	False	False	* Proposed schedule for remediation (note if remediation plan timeline is more than 90 days OCD approval is required)
Scaled Site Map	Remediation Closure Request - Scaled Site Map	False	False	* A scaled site and sampling diagram as described in 19.15.29.11 NMAC
Photographs	Remediation Closure Request - Photographs	False	False	* Photographs of the remediated site prior to backfill or photos of the liner integrity if applicable (Note: appropriate OCD District office must be notified 2 days prior to liner inspection)
Lab Samples OR Liner Integrity	Remediation Closure Request - Lab Samples OR Liner Integrity Report	False	False	* Laboratory analyses of final sampling or liner integrity certification (Note: appropriate ODC District office must be notified 2 days prior to final sampling)
Remediation Activities	Remediation Closure Request - Remediation Activities	False	False	* Description of remediation activities
Scaled Site Map	Reclamation Report - Scaled Site Map	False	False	* Scaled site map showing reclaimed production area, reclaimed non-production area, errosion control features, and any site ponding.
Photographs	Reclamation Report - Photographs	False	False	* Photographs of the reclamation site after backfill and recontouring has been completed
Reseeding Plan	Reclamation Report - Proposed Reseeding Plan	False	False	* Proposed plan to revegetate site, specifically indicating reseeding mixture, identify next growing season and intended start date
Reclamation Activities	Reclamation Report - Reclamation Activities	False	False	* Description of remediation activities
Scaled Site Map	Revegetation Report - Scaled Site Map	False	False	* Scaled site map showing revegetated area, sample control area(s), points of evaluation for life form ratio and plant coverage.
Photographs	Revegetation Report - Photographs	False	False	* Photographs of the site after revegetation efforts have been evaluated
Revegetation Activities	Revegetation Report - Revegetation Activities	False	False	* Description of revegetation activities including a statement of completion OR an updated proposed reseeding plan

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Remediation Activities	Remediation Activities	True	False	* Description of remediation activities

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve

Click again to collapse NMAC

19.15.7.8 D. (52)       form C-141 - release notification and corrective action;

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144B	Main Form	True	True
Request For Variance	Request For Variance	False	False
Siting Criteria	Siting Criteria	False	False
Site Map/Topo	Site Map/Topo	False	False
C-102	C-102	False	False	* Plat Survey (Pad Diagram)
Depth to Water	Depth to Water	False	False
Site Specific Hydro Geologic	Site Specific Hydro Geologic	False	False
Design and Construction Plan	Design and Construction Plan	False	False
Design Drawing	Design Drawing	False	False
Operation and Maintenance Plan	Operation and Maintenance Plan	False	False
Closure Plan	Closure Plan	False	False
Closure Report	Closure Report	False	False
C-105 Rig release Date (Closure)	C-105 Rig release Date (Closure)	False	False
C-141	C-141	False	False	* Indicating Results
Laboratory Analysis Results	Laboratory Analysis Results	False	False
Photographs	Photographs	False	False
Construction Notifications	Construction Notifications	False	False
Closure Sampling Notifications	Closure Sampling Notifications	False	False
Reclamation Notification	Reclamation Notification	False	False
List of Permitted Wells	A list of wells with approved permits to drill multiwell pits	False	False
Operator inspections	Operator inspections	False	False
Deed Notice	Copy of Deed Notice with county clerk	False	False	* If on private land
H2S Plan	H2S Plan	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144E	Main Form	True	True
Request For Variance	Request For Variance	False	False
Siting Criteria	Siting Criteria	False	False
Site Map/Topo	Site Map/Topo	False	False
C-102	C-102	False	False	* Plat Survey (Pad Diagram)
Depth to Water	Depth to Water	False	False
Site Specific Hydro Geologic	Site Specific Hydro Geologic	False	False
Design and Construction Plan	Design and Construction Plan	False	False
Design Drawing	Design Drawing	False	False
Operation and Maintenance Plan	Operation and Maintenance Plan	False	False
Closure Plan	Closure Plan	False	False
Closure Report	Closure Report	False	False
C-105	C-105	False	False	* Rig release Date (Closure)
C-141	C-141	False	False	* Indicating Results
Laboratory Analysis Results	Laboratory Analysis Results	False	False
Photographs	Photographs	False	False
Construction Notifications	Construction Notifications	False	False
Closure Sampling Notifications	Closure Sampling Notifications	False	False
Reclamation Notification	Reclamation Notification	False	False
List of Permitted Wells	A list of wells with approved permits to drill multiwell pits	False	False
Operator inspections	Operator inspections	False	False
Deed Notice	Copy of Deed Notice with county clerk	False	False	* If on private land
H2S Plan	H2S Plan	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144M	Main Form	True	True
Request For Variance	Request For Variance	False	False
Siting Criteria	Siting Criteria	False	False
Site Map/Topo	Site Map/Topo	False	False
C-102	C-102	False	False	* Plat Survey (Pad Diagram)
Depth to Water	Depth to Water	False	False
Site Specific Hydro Geologic	Site Specific Hydro Geologic	False	False
Design and Construction Plan	Design and Construction Plan	False	False
Design Drawing	Design Drawing	False	False
Operation and Maintenance Plan	Operation and Maintenance Plan	False	False
Closure Plan	Closure Plan	False	False
Closure Report	Closure Report	False	False
C-105	C-105	False	False	* Rig release Date (Closure)
C-141	C-141	False	False	* Indicating Results
Laboratory Analysis Results	Laboratory Analysis Results	False	False
Photographs	Photographs	False	False
Construction Notifications	Construction Notifications	False	False
Closure Sampling Notifications	Closure Sampling Notifications	False	False
Reclamation Notification	Reclamation Notification	False	False
List of Permitted Wells	A list of wells with approved permits to drill multiwell pits	False	False
Operator inspections	Operator inspections	False	False
Deed Notice	Copy of Deed Notice with county clerk	False	False	* If on private land
H2S Plan	H2S Plan	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144P	Main Form	True	True
Request For Variance	Request For Variance	False	False
Siting Criteria	Siting Criteria	False	False
Site Map/Topo	Site Map/Topo	False	False
C-102	C-102	False	False	* Plat Survey (Pad Diagram)
Depth to Water	Depth to Water	False	False
Site Specific Hydro Geologic	Site Specific Hydro Geologic	False	False
Design and Construction Plan	Design and Construction Plan	False	False
Design Drawing	Design Drawing	False	False
Operation and Maintenance Plan	Operation and Maintenance Plan	False	False
Closure Plan	Closure Plan	False	False
Closure Report	Closure Report	False	False
C-105	C-105	False	False	* Rig release Date (Closure)
C-141	C-141	False	False	* Indicating Results
Laboratory Analysis Results	Laboratory Analysis Results	False	False
Photographs	Photographs	False	False
Construction Notifications	Construction Notifications	False	False
Closure Sampling Notifications	Closure Sampling Notifications	False	False
Reclamation Notification	Reclamation Notification	False	False
List of Permitted Wells	A list of wells with approved permits to drill multiwell pits	False	False
Operator inspections	Operator inspections	False	False
Deed Notice	Copy of Deed Notice with county clerk	False	False	* If on private land
H2S Plan	H2S Plan	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144T	Main Form	True	True
Request For Variance	Request For Variance	False	False
Siting Criteria	Siting Criteria	False	False
Site Map/Topo	Site Map/Topo	False	False
C-102	C-102	False	False	* Plat Survey (Pad Diagram)
Depth to Water	Depth to Water	False	False
Site Specific Hydro Geologic	Site Specific Hydro Geologic	False	False
Design and Construction Plan	Design and Construction Plan	False	False
Design Drawing	Design Drawing	False	False
Operation and Maintenance Plan	Operation and Maintenance Plan	False	False
Closure Plan	Closure Plan	False	False
Closure Report	Closure Report	False	False
C-105	C-105	False	False	* Rig release Date (Closure)
C-141	C-141	False	False	* Indicating Results
Laboratory Analysis Results	Laboratory Analysis Results	False	False
Photographs	Photographs	False	False
Construction Notifications	Construction Notifications	False	False
Closure Sampling Notifications	Closure Sampling Notifications	False	False
Reclamation Notification	Reclamation Notification	False	False
List of Permitted Wells	A list of wells with approved permits to drill multiwell pits	False	False
Operator inspections	Operator inspections	False	False
Deed Notice	Copy of Deed Notice with county clerk	False	False	* If on private land
H2S Plan	H2S Plan	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144LB	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
PIT INVENTORY	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144	Main Form	True	True

Click again to collapse NMAC

19.15.7.8 D. (53)       form C-144 - pit, closed-loop system, below-grade tank or proposed alternative method permit or closure plan application;

Click again to collapse NMAC

19.15.7.8 D. (54)       form C-145 - change of operator; and

Click again to collapse NMAC

19.15.7.8 D. (55)       form C-146 - change of operator name.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-147L	Main Form	True	True
Request For Variance	Request For Variance	False	False
Site Map/Topo	Site Map/Topo	False	False
Siting Criteria	Siting Criteria	False	False
Depth to Water	Depth to Water	False	False
Site Specific Hydro Geologic	Site Specific Hydro Geologic	False	False
Design and Construction Plan	Design and Construction Plan	False	False
Operation and Maintenance Plan	Operation and Maintenance Plan	False	False
Closure Plan	Closure Plan	False	False
Engineer Closure Cost Estimate	Engineer Closure Cost Estimate	False	False
Engineer Design Drawings	Engineer Design Drawings	False	False
Surface Owner Notification	Surface Owner Notification	False	False
Variance Attachments	Variance Attachments	False	False
As Built Drawings	As Built Drawings	False	False
Closure Report	Closure Report	False	False
Laboratory Analysis Results	Laboratory Analysis Results	False	False
Photographs	Photographs	False	False
Inspection Reports	Inspection Reports	False	False
Construction Notices	Construction Notices	False	False
Cessation Notices	Cessation of Operations Extension Notices	False	False
Closure Notice	Closure Notice	False	False
Reclamation Notice	Reclamation Notice	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-147S	Main Form	True	True
Request For Variance	Request For Variance	False	False
Site Map/Topo	Site Map/Topo	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Request for Hearing	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Motion to Continue	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Motion to Dismiss	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Motion	Main Form	True	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Entry of Appearance	Main Form	True	True
Affidavit	Affidavit	False	False
Exhibit	Exhibit	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Notice of Intervention	Main Form	True	True
Affidavit	Affidavit	False	False
Exhibit	Exhibit	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Prehearing Statement	Main Form	True	True
Affidavit	Affidavit	False	False
Exhibit	Exhibit	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Affidavit	Main Form	True	True
Exhibit	Exhibit	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Exhibit	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Post Hearing Statement	Main Form	True	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Order Compliance/Progress Report	Main Form	True	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
AFFIDAVIT - CONVERSION TO WATER WELL	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Bradenhead Test	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
DISCHARGE PERMIT NOI	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
DISCHARGE PERMIT	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
DISCHARGE PLAN BRINE EXTRACTION NOI	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
DISCHARGE PLAN BRINE EXTRACTION	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
DISCHARGE PLAN SERVICE COMPANIES NOI	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
DISCHARGE PLAN SERVICE COMPANIES	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Site Plan	Site Plan	False	False
Photos	Site Photographs	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Site Plan	Site Plan	False	False
Photos	Site Photographs	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Site Plan	Site Plan	False	False
Photos	Site Photographs	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Pending Installation List	Flare Stacks Installed After Rule Effective Pending Installation List	False	False	* Required if at least one flare stack "installed May 25, 2021 or later without the required equipment" is indicated
Low Production List	Flare Stacks Installed Prior to Rule Effective Low Production List	False	False	* Required if at least one flare stack "installed Prior to May 25, 2021 at location production less than or equal to 60 MCF" is indicated
Pending Retrofit List	Flare Stacks Installed Prior to Rule Effective Pending Retrofit List	False	False	* Required if at least one flare stack "installed Prior to May 25, 2021 at location production more than 60 MCF requiring retrofit" is indicated

Click again to collapse NMAC

19.15.2.7 D. (6)       “Downstream facility” means a facility associated with the transportation (including gathering) or processing of gas or oil (including a refinery, gas plant, compressor station or crude oil pump station); brine production; or the oil field service industry.
            F. (1)       “Facility” means a structure, installation, operation, storage tank, transmission line, access road, motor vehicle, rolling stock or activity of any kind, whether stationary or mobile.
            G. (5)       “Gas transportation facility” means a pipeline in operation serving gas wells for the transportation of gas, or some other device or equipment in like operation where the gas produced from gas wells connected with the pipeline or other device or equipment can be transported or used for consumption.
            S. (11)       “Surface waste management facility” means a facility that receives oil field waste for collection, disposal, evaporation, remediation, reclamation, treatment or storage except:
                                    a)       a facility that utilizes underground injection wells subject to division regulation pursuant to the federal Safe Drinking Water Act, and does not manage oil field wastes on the ground in pits, ponds, below-grade tanks or land application units;
                                    b)       a facility permitted pursuant to the New Mexico environmental improvement board rules or WQCC rules;
                                    c)       a temporary pit as defined in 19.15.17 NMAC;
                                    d)       a below-grade tank or pit that receives oil field waste from a single well, permitted pursuant to 19.15.37 NMAC, regardless of the capacity or volume of oil field waste received;
                                    e)       a facility located at an oil and gas production facility and used for temporary storage of oil field waste generated on-site from normal operations, if the facility does not pose a threat to fresh water, public health, safety or the environment;
                                    f)       a remediation conducted in accordance with a division-approved abatement plan pursuant to 19.15.30 NMAC, a corrective action pursuant to 19.15.29 NMAC or a corrective action of a non-reportable release;
                                    g)       a facility operating pursuant to a division emergency order;
                                    h)       a site or facility where the operator is conducting emergency response operations to abate an immediate threat to fresh water, public health, safety or the environment or as the division has specifically directed or approved; or
                                    i)       a facility that receives only exempt oil field waste, receives less than 50 barrels of liquid water per day (averaged over a 30-day period), has a capacity to hold 500 barrels of liquids or less and is permitted pursuant to 19.15.17 NMAC.
            U. (7)       “Upstream facility” means a facility or operation associated with the exploration, development, production or storage of oil or gas that is not a downstream facility.

19.15.27.8 G. (2)       Monthly reporting of vented and flared natural gas. For each well or facility at which venting or flaring occurred, the operator shall separately report the volume of vented natural gas and volume of flared natural gas for each month in each category listed below. Beginning October 1, 2021, the operator shall gather data for quarterly reports in a format specified by the division and submit by February 15, 2022 for the fourth quarter and May 15, 2022 for the first quarter. Beginning April 2022, the operator shall submit a form C-115B monthly on or before the 15th day of the second month following the month in which it vented or flared natural gas. The operator shall specify whether it estimated or measured each reported volume. In filing the initial report, the operator shall provide the methodology (measured or estimated using calculations and industry standard factors) used to report the volumes and shall report changes in the methodology on future forms. The operator shall make and keep records of the measurements and estimates, including records showing how it calculated the estimates, for no less than five years and make such records available for inspection by the division upon request.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
GAS ANALYSIS	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
GROUND WATER ABATEMENT	Main Form	True	True
Cover letter/ executive summary	Cover letter/ executive summary	False	False
Variance request page	Variance request page	False	False
Current report period activity	Current report period activity	False	False
Plans for next reporting period	Plans for next reporting period	False	False
Siting Criteria	Siting Criteria	False	False
Site Map/Aerials/Topos	Site Map/Aerials/Topos	False	False
Site Characterization	Site Characterization	False	False
Remediation Work Plan	Remediation Work Plan	False	False
Ground Water Gradient	Ground Water Gradient	False	False
Ground Water Plume	Ground Water Plume	False	False
Historic Depth to Water	Historic Depth to Water	False	False
Historic Ground Water Sampling	Historic Ground Water Sampling	False	False
Surface Owner List	Surface Owner List	False	False
Public Notice	Public Notice	False	False
Laboratory Analysis Results	Laboratory Analysis Results	False	False
Photographs	Photographs	False	False
Monitor Well Lithology/Construction	Monitor Well Lithology/Construction	False	False
Cross Sections	Cross Sections	False	False
Field Data	Field Data	False	False
Closure Request	Closure Request	False	False
Sampling Notice	Sampling Notice	False	False
Public Notice Comments	Public Notice Comments	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
H2S Plan	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
HBP	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
HIP NOI	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
HIP	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Gas Capture Rate Adjustment Request	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Gas Capture Rate Compliance Plan	Main Form	True	True

Click again to collapse NMAC

19.15.27.9 A. (3)       An operator’s acquisition or sale of one or more wells from another operator shall not affect its annual natural gas capture requirements. No later 60 days following the acquisition or sale, the operator may file a written request to the division requesting to modify its gas capture percentage requirements for good cause based on its acquisition or sale. The division may approve, approve with conditions, or deny the request in its sole discretion.
                        (4)       No later than March 30 following the reporting year, an operator that has not met its annual natural gas capture requirement for the previous year shall submit to the division a compliance plan demonstrating its ability to comply with its annual gas capture requirement for the current year. If the division determines, after a reasonable opportunity to meet with the operator, that the compliance plan does not demonstrate the operator’s ability to comply with its annual gas capture requirement for the current year the operator’s approved APDs for wells that have not been spud shall be suspended pending a division hearing to be held no later than 30 days after the determination. Nothing in this subparagraph shall prevent the division from taking any other action authorized by law for the operator’s failure to comply with its annual gas capture requirement, including shutting in wells and assessing civil penalties.
            B.       Accounting. No later than February 28 of each year beginning in 2023, the operator shall submit a report certifying compliance with its statewide gas capture requirements. The operator shall determine compliance with its statewide gas capture requirements by deducting any ALARM credits approved pursuant to this subsection from the aggregated volume of lost gas calculated for each month during the preceding year pursuant to Subparagraph (a) of Paragraph (3) of Subsection G of 19.15.27.8 NMAC, deducting that aggregated volume of lost gas from the aggregated volume of natural gas produced for each month during the preceding year, and dividing that volume by the aggregated volume of natural gas produced for each month during the preceding year.
            D. (6)       If, at any time after the operator submits the natural gas management plan and before the well is spud:
                                    (b)       the operator becomes aware that it has, cumulatively for the year, become out of compliance with its baseline natural gas capture rate or natural gas capture requirement, no later than 20 days after becoming aware of such information, the operator shall submit for the division’s approval a new or revised natural gas management plan for each well it plans to spud during the next 90 days containing the information specified in Paragraph (2) of Subsection D of 19.15.27.9 NMAC, and shall file an update for each plan until the operator is back in compliance with its baseline natural gas capture rate or natural gas capture requirement.

19.15.28.10 A. (3)       An operator’s acquisition or sale of a natural gas gathering system from another operator shall not affect its annual natural gas capture requirements. No later 60 days following the acquisition or sale, the operator may file a written request to the division requesting to modify its annual gas capture percentage requirements for good cause based on its acquisition or sale. The division may approve, approve with conditions, or deny the request in its sole discretion.
            B.       Accounting. No later than February 28 of each year beginning in 2023, the operator shall submit a report certifying compliance with its statewide gas capture requirements. The operator shall determine compliance with its statewide gas capture requirements by deducting any ALARM credits approved pursuant to this subsection from the aggregated volume of lost gas calculated for each month during the preceding year pursuant to Subparagraph (a) of Paragraph (3) of Subsection F of 19.15.28.8 NMAC, deducting that aggregated volume of lost gas from the aggregated volume of natural gas gathered for each month during the preceding year, and dividing that volume by the aggregated volume of natural gas gathered for each month during the preceding year.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Site Plan	Site Plan	False	False
Photos	Site Photographs	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Map	Main Form	True	True	As built map see ... for GIS schema.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Operations Plan	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Confidentiality Request	Main Form	True	True

Click again to collapse NMAC

19.15.28.7 L.       “Natural gas gathering system” means the gathering pipelines and associated facilities that compress, dehydrate or treat natural gas after the custody transfer point and ending at the connection point with a natural gas processing plant or transmission or distribution system.

19.15.28.8 F. (2)       For each natural gas gathering system at which venting or flaring occurred, the operator shall separately report the volume of vented natural gas and the volume of flared natural gas for each month in each category listed below. Beginning October 1, 2021, the operator shall gather data for quarterly reports in a format specified by the division and submit by February 15, 2022 for the fourth quarter of 2021 and May 15, 2022 for the first quarter of 2022. Beginning April 2022, the operator shall submit a form C-115B monthly on or before the 15th day of the second month following the month in which it vented or flared natural gas. The operator shall specify whether it estimated or measured each reported volume. In filing the initial report, the operator shall provide the methodology (measured or estimated using calculations and industry standard factors) used to report the volumes on the form, and shall report changes in the methodology on future forms. The operator shall make and keep records of the measurements and estimates, including records showing how it calculated the estimates, for no less than five years and make such records available for inspection by the division upon request.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
NGMP	Main Form	True	True
Best Management Practices	Best Management Practices to minimize venting during active and planned maintenance	True	True
Operational Practices	Operational Practices	True	True
Separation Equipment	Description of separation equipment sizing to optimize gas capture	True	True
Certification of take away	Certification of take away or attached venting or flaring plan	True	True
Route Map	Map of well(s) location and anticipated pipeline route, including maximum daily capacity	False	False
Line Pressure Plan	Line Pressure Plan to manage production in response to the increased line pressure	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
GAS CAPTURE PLAN	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
NSL	Main Form	True	True	* Typically the request for approval or a statement from counsel
C-102	C-102	True	False
Affected Persons	List of affected persons entitled to notice of the application	True	False
Proof of Notices	Notices to the designated parties, by certified mail	True	False	* Return receipt requested, specifying the proposed well’s location and depth
Formation Reasons	Reasons for the formation of the non-standard spacing unit	True	False
Ownership Plats	Plats of surface ownership of existing wells producing from same pool	True	False	* Including wells operated by any other operators

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
NSP	Main Form	True	True	* Typically the request for approval or a statement from counsel
C-102	C-102	True	False
Affected Persons	List of affected persons entitled to notice of the application	True	False
Proof of Notices	Notices to the designated parties, by certified mail	True	False	* Return receipt requested, specifying the proposed well’s location and depth
Formation Reasons	Reasons for the formation of the non-standard spacing unit	True	False
Ownership Plats	Plats of surface ownership of existing wells producing from same pool	True	False	* Including wells operated by any other operators

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Site Photographs	Pre-Plug Site Photographs	False	False
Aerial Survey	Aerial Survey	False	False
Support Doc	Supporting Documentation	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Support Doc	Supporting Documentation	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Tech Report	Technical Report	True	True
Test Report	Test Report	False	False
Gas Analysis	Gas Analysis	False	False
Test Data	Test Data	False	False
Photos	Site Photographs	False	False
Support Doc	Supporting Documentation	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103F	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
Plugging Plan	Plugging Plan	True	True
Current Wellbore Schematic	Current Wellbore Schematic	True	True
Proposed Wellbore Schematic	Proposed Wellbore Schematic	True	True
BLM COA	BLM Conditions Of Approval	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Decommission Plan	Decommission Plan	True	True
Current Site Diagram	Current Site Diagram	True	True
Proposed Site Diagram	Proposed Site Diagram	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-103P	Main Form	True	True	* An operator of a well on federal land shall use the BLM Form 3160-5 in lieu of division Form C-103
Plugging Report	Plugging Report	True	True
Wellbore Schematic	Wellbore Schematic	True	True	* Subsequent wellbore schematic needs to reflect downhole conditions and any adjustments made during plugging operations. If no changes were made from NOI refile previous wellbore schematic for completed P&A record.
Site Photographs	Post-Plug Site Photographs	True	True	* Subsequent wellbore schematic needs to reflect downhole conditions and any adjustments made during plugging operations. If no changes were made from NOI refile previous wellbore schematic for completed P&A record.

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Tech Report	Technical Report	True	True
Gas Analysis	Gas Analysis	False	False
Photos	Site Photographs	False	False
Support Doc	Supporting Documentation	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144W	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
C-144F	Main Form	True	True

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Marker Photographs	Marker Photographs	True	True
Site Photographs	Site Photographs	False	False
Pipeline Layout	Pipeline layout including legal description and surface ownership	False	False	* Required if leaving pipeline(s)
Radiation Survey	Results of radiation survey along pipeline route	False	False	* Required if leaving pipeline(s)
Pipeline Material Type	Type of material used the pipeline	False	False	* Required if leaving pipeline(s)
Pipeline Flushing Procedure	Procedure used for flushing pipeline	False	False	* Required if leaving pipeline(s)
Explanation of Benefit	Explanation why it is more beneficial to leave the pipeline	False	False	* Required if leaving pipeline(s)
Proof of Notice	Proof notices sent to all surface owners where the pipeline is located	False	False	* Required if leaving pipeline(s)

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Site Photographs	Site Photographs	True	True
Pipeline Layout	Pipeline layout including legal description and surface ownership	False	False	* Required if leaving pipeline(s)
Radiation Survey	Results of radiation survey along pipeline route	False	False	* Required if leaving pipeline(s)
Pipeline Material Type	Type of material used the pipeline	False	False	* Required if leaving pipeline(s)
Pipeline Flushing Procedure	Procedure used for flushing pipeline	False	False	* Required if leaving pipeline(s)
Explanation of Benefit	Explanation why it is more beneficial to leave the pipeline	False	False	* Required if leaving pipeline(s)
Proof of Notice	Proof notices sent to all surface owners where the pipeline is located	False	False	* Required if leaving pipeline(s)

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Daily Details	Daily Details Report	True	True
Cleanup	Cleanup Details Report	False	False
Per Diem Pre-Approval	Environmental Personnel Per Diem Allowance Pre-Approval	False	False
Other	Supporting Documentation	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Daily Details	Daily Details Report	True	True
Cement	Cement Details Report	False	False
Per Diem Pre-Approval	Environmental Personnel Per Diem Allowance Pre-Approval	False	False
Other	Supporting Documentation	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Invoice	Invoice	True	True
Third Party	Third Party Invoice	False	False
Vendor Items	Itemized Vendor Provided Items	False	False
Lab Services	Itemized Laboratory Analytical Services	False	False
Estimate Costs	Estimate Remaining Work, Scope and Costs	False	False
Item Salvage	Itemized List of (any anticipated) Item Salvage	False	False
Other	Supporting Documentation	False	False

Click again to collapse

Description		Required to		Note
Tag	Attachment Type	Submit	Approve
Invoice	Invoice	True	True
Third Party	Third Party Invoice	False	False
Vendor Items	Itemized Vendor Provided Items	False	False
Lab Services	Itemized Laboratory Analytical Services	False	False
Estimate Costs	Estimate Remaining Work, Scope and Costs	False	False
Item Salvage	Itemized List of (any anticipated) Item Salvage	False	False
Other	Supporting Documentation	False	False